Force Analysis of Material Movement in a Horizontal Mixer of a Hydrolytic Chamber: a Case Study of Soybean Meal Processing

The paper addresses the increasing demand for plant-based protein in the compound feed industry. It emphasizes the role of grain legumes; particularly soy; one of the most protein-rich crops; as a primary feed protein source. Analytical studies have identified key strategies for developing a universal compound feed production line that integrates high-protein ingredients derived from soybean meal. To enhance protein digestibility and biological value; extruded soybean meal undergoes enzymatic hydrolysis in a continuous horizontal mixer. Additionally; the paper describes material movement within a hydrolytic chamber equipped with a screw-driven working unit. (Research purpose) The primary objective of the study is to conduct a force analysis of material movement in a horizontal screw mixer to determine the optimal structural and operational parameters of the hydrolytic chamber. (Materials and methods) The analysis focuses on the system of forces acting on a material particle resting on the helical surface of a horizontal screw and pressed against the inner wall of the casing. (Results and discussion) By projecting all active and assumed inertial forces acting on a material particle; a system of equations was derived. The study found that the power required to drive the screw shaft depends on multiple factors; including the condition of the screw and casing surfaces; particle mass; screw geometry; polar coordinates defining the particle’s position within the screw; and the kinematic parameters of its rotational motion. (Conclusions) The developed mathematical model of material movement; which accounts for the physical and mechanical properties of the material and the geometry of its flow; facilitates the selection of optimal structural and operational parameters for the mixer. This ensures efficient material transport during the design process.

1. Milushev R.K., Epifanov V.G. The use of protein concentrates from vegetable raw materials for replacement in compound feed of feed of animal origin. Feeding of Agricultural Animals and Feed Production. 2019. N5. 48-68 (In Russian). EDN: STLKGL.

2. Bulatov S.Yu., Simachkova M.S., Sergeev A.G. et al. Features of the production of compound feeds in the conditions of agricultural organizations in modern realities. Bulletin NGIEI. 2022. N10(137). 59-67 (In Russian). DOI: 10.24412/2227-9407-2022-10-59-67.

3. Dorokhov A.S., Zagoruiko M.G., Maradudin A.M., Bashmakov I.A. Material movement within a single-screw extruder. Inmateh – Agricultural Engineering. 2021. N3(65). 421-429 (In English). DOI: 10.35633/INMATEH-65-44.

4. Savinykh P.A., Aleshkin A.V., Turubanov N.V., Zyrya­nov D.A. Determination of mixer tap’s rational para­meters by theoretical studies of the interaction of the screw’s helix surface with the material. Machinery and Technologies in Livestock. 2021. N1(41). 76-84 (In Russian). DOI: 10.51794/27132064-2021-1-76.

5. Shagarova A.A., Shaposhnikov A.P., Tarasenko L.E. Rheo­metric studies of high-viscosity fluid flow characteristics in the schneck machines with a thin wall layer. Izvestia Volgograd State Technical University. 2014. N1(128). 87-90 (In Russian). EDN: RVFVUZ.

6. Petrenko S.S., Chernenko G.V., Adigamov K. The use of a screw conveyor with a finned cover as a working body of the mixer bulk materials. Modern Problems of Science and Education. 2013. N4. 77-82 (In Russian). EDN: ROFSQJ.

7. Zubkova T.M., Mustyukov N.A., Tokareva M.A. Single screw extruder engineering with artificial intelligence elements. Software & Systems. 2016. Vol. 29. N4. 176-182 (In Russian). DOI: 10.15827/0236-235X.116.176-182.

8. Braginets S.V., Khlystunov V.F., Bakhchevnikov O.N. et al. Study of the process of mixing fodder components in a horizontal mixer. AIC development problems of the region. 2016. N3(27). 110-114 (In Russian). DOI: 10.15217/issn2079-0996.2016.3.

9. Evstarova A.V. Regularities of the drilling fines flow on the screw surface of the auger at drilling of vertical boreholes. Mining Information-Analytical Bulletin. 2007. N3. 306-312 (In Russian). EDN: RGRBLH.

10. Zagoruiko M.G., Vasilchikov V.V., Mamakhai A.K. Simu­lation of the extruder screw parameters. Agricultural Machinery and Technologies. 2020. N4(14). 71-77 (In Russian). DOI: 10.22314/2073-7599-2020-14-4-71-77.

11. Protasov A.A., Makarov S.A., Danilin A.V., Levchenko G.V. Theoretical studies of kinematic parameters of material motion in a press-extruder. Agrarian Scientific Journal. 2019. N12. 105-109 (In Russian). DOI: 10.28983/asj.y2019i12pp105-109.

12. Brusenkov A.V., Konovalov D.N. Development, design and methodology for calculating the structural and technological characteristics of a screw grinder of root crops. Vestnik Mashinostroeniya. 2022. N10. 24-31 (In Russian). DOI: 10.36652/0042-4633-2022-10-24-31.

13. Zagoruiko M.G., Dorohov A.S., Maradudin A.M. Substantiation of the basic parameters of the screw expander for processing high protein crops. Niva Povolzhya. 2020. N2(55). 124-131 (In Russian). DOI: 10.36461/NP.2020.2.55.019.

14. Zubelevich O.E. The D’Alembert - Lagrange principle: a geometrical aspect. Journal of Applied and Industrial Mathematics. 2020. N3(83). 31-39 (In Russian). DOI: 10.33048/SIBJIM.2020.23.303.

15. Bogdanova S.B., Gladkov S.O. On the trajectories of bodies in non-inertial reference frames. Tomsk State University Journal of Mathematics and Mechanics. 2023. N84. 6880 (In Russian). DOI: 10.17223/19988621/84/6.

16. Marczuk A., Misztal W., Savinykh P.et al. Improving efficiency of horizontal ribbon mixer by optimizing its constructional and operational parameters. Eksploatacja i niezawodnosc. 2019. N2(21). 220-225 (In English). DOI: 10.17531/ein.2019.2.5.

17. Bulatov S.Yu., Nechaev V.N., Pronin A.N., Sergeev A.G. Results of studies of the working process of a screw feeder for dry bulk components with a stepper motor. Machine­ry and Equipment for Rural Area. 2024. N1(319). 33-36 (In Russian). DOI: 10.33267/2072-9642-2024-1-33-36.